Saranya Electronics   Home | SiteMap | Location
 
Our Products
DESTINATION BOARD DISPLAY SYSTEM
INTEGRATED PASSENGER INFORMATION   SYSTEMS
LAPTOP / MOBILE CHARGER FOR COACHES
GANG / WORKSITE REMOTE CONTROL HOOTER
ELECTRIC LIFTING BARRIER WITH HAND   GENRATOR
CONTINUOUS RAIL THERMOMETER
LED BASED HAND SIGNAL LAMP
LED BASED TAIL LAMP
LED BASED GPS CLOCKS 
LED BASED CHART READING LIGHT
PROGRAMMABLE STREET LIGHT CONTROL   SWITCH
LED BASED EMERGENCY LIGHT
ULTRA LITE MINER CAP LAMP
Read More
Consumer Products
Solar power Invertors 800 VA with 200W/   400W/ 800W panels with LED lamps and DC   fans
Solar power Lanterns with mobile   charger
Programmable school bells
Home security systems
LED display boards for banks are   commercial establishments
GPS clocks for hospitals, commercial   establishment, function halls and   industries.
Environmental friendly toilets   employing bio digester technology
Solar motors
Solar LED home lighting system
Read More
Rrder Now
Products   >   Programmable Street Light Control
PROGRAMMABLE STREET LIGHT CONTROL
 
 
Everything you know about power is outdated. That’s the truth. It’s a whole new way of working and thinking. This revolutionary device is as close as you get to have someone else do your work for you,by your own choice of timing. The Intelligent switch’s unique capabilities make it the smart little device you have been waiting for. The high reliability assures unattended operation.Saranya Electronics Pvt.Ltd has incorporated years of experience, continual technical advances and expert know-how to make this intelligent time switch. It delivers high performance, reliability and  quality.
controlswith  
FEATURES:  
   
  • Programmable street light ON/OFF control at predetermined timings over entire one year based on city almanac data at rated load & at rated power factor

  • User satellite based GPS timings eliminating defects like corruption of timing data noticed in the real time clock based switches due to surges/spikes prevalent with electric distribution network.

  • Facility for manual switching bypassing the programmed switching in case of any unexpected requirement.

  • Protection against over voltage of above 260volts and under voltage of below 160 volts. The system disconnects light load with in  twenty millisecs  thus protecting the bulbs against voltage fluctuations.

  • The body /all accessible parts from outside are maintained at ground  potential by connecting the same to earth through metal strip thus providing fool proof protection for operating personnel.

  • Optional feature to switch on street lights when ambient light falls below 60lux and to switch off when ambient lights is more then 80 Lux  or alternatively at predetermined time interval  after getting switched on based on the above light sensing. The light detector used is immune to moon light.

  • In case of power failure, auto recovery relay is built in to facilitate automatic switching on of street lights upon recovery of power.

  • 20% power saving in case of single phase and 30% saving in case of three phase circuits.

  • The lights can be programmed to switch ON/OFF alternative street lights at required timings.

  • LCD based display of precise timings provided.

  • The switch enclosed in sheet  metal enclosure pretreated and duly power coated  confirming to degree of protection IP No of  IS: 12063/1999.It  is possible to mount the switch on prestressed concrete poles or circular or l –shaped poles.

  • The switch is also protected against surges and spikes. All live parts shall with stand the high voltage test of 1.5kv for one minute Assured insulation resistance of five mega ohms between live parts and ground.

  • The switch undergoes rigorous burn in test for 48hours at 45degrees centigrade at full load besides Dry Heat, Damp Heat and cold test as per IS:9000prior to dispatch.

  • Typical System Composition:

    a) Micro controller  card with GPS receiver

    b) EMI/Spike protection unit

    c) MCB  protection unit

    d) Single phase60amps/100amps relay unit

    e) 100anps terminal box

    f) Outer metallic enclosure/box with suitable Clamping arrangement(20”x13”x6.5”).

  • Recovering investment due to switch cost is possible with in 160 days to power savings affected in programmed  switching.
 
   
 
Home  |  About Us  |  Careers  |  Products  |  Press Release  |  Feed Back   |  Contact Us
All Rights Reserved © www.saranyaelectronics.com Powered by Weblabs